NOT ALL RJ-45S ARE CREATED EQUAL
FEATURING SENTINEL CONNECTOR SYSTEMS - WHEN SIGNAL INTEGRITY MATTERS
          Shipping Over 100,000,000 RJ45 Plugs a Year - MADE in USA

Cage Code 71SB6   DUNS 191497254    P:630-659-6337    dave@rj45s.com
             
106-08080058-34 or 111-08080090L34
RJ45 Plugs for Belden 7922A Category 5e DataTuff Cable

 




     
BELDEN® Category 5e DataTuff® Twisted Pair Cable

7922A - 22 AWG Bonded-Pairs solid bare copper conductors, polyolefin insulation, industrial grade sunlight- and Oil-resistant PVC jacket, rip cord. Sequential marking at two foot intervals.


NOTE: SPECIAL TERMINATION INSTRUCTIONS - SLIDE ON HEAT SHRINK TUBING, STRIP OFF JACKET, TERMINATE, PULL HEAT SHRINK OVER REAR OF PLUG AND SHRINK
GOOD

106-08080058-34

Stocked


BETTER

111-08080090L34

Stocked
106-08080058-34 and 111-08080090L34 Product Features

*   Incorporates a PATENTED CONDUCTIVE NEXT Reduction System. In addition to providing PRECISE CONDUCTOR ALIGNMENT, the Composite Carbon/Graphite Fiber Conductor Load Bar GREATLY REDUCES NEXT and RETURN LOSS by ABSORBING REFLECTIONS and CHANNELING IT AWAY FROM THE CONDUCTORS. Using recommended termination procedures and equipment, ANSI/TIA/EIA 568 Category 6 performance levels are achievable with good workmanship and certified cables.
*   Utilizes a 4 over 4 contact design (4 LONG and 4 SHORT) that provides increased isolation and spatial dispersion within the plug to minimize crosstalk and 111S08080090L34 accepts .044" - 048" CONDUCTOR OD. 106-08080058-34 accepts up to .048" CONDUCTOR OD.
*   The conductors are isolated by the Conductor Load Bar and through Plastic Isolation/Insulation Barriers where contact termination is made, thereby improving electrical performance.
  Plug accepts both SOLID or STRANDED conductors
*   Made in USA

106-08080058-34 Specifications 
111-08080090L34 Specifications
 

Performance:    Meets or Exceeds ANSI/TIA 568-C.2 - ANSI/TIA 1096-B (Formerly FCC Part 68) - CENELEC EN 50173 -    
IEC 60603 - ISO-8877 - ISO/IEC 11801
Contact Material:   Phosphor Bronze - .012" thick
Contact Plating:   Minimum 50 Micro-Inch Pure Gold - Selective 24 Carat Hard Gold Plate in contact area over 100 Micro-Inch minimum Nickel Plate. Exceeds TIA-1096 specifications (formerly FCC Part 68)
Plug Material:   Polycarbonate
Plug Tolerances and Dimensions:   Meets TIA-1096 specifications (formerly FCC Part 68)
UL Recognized:   UL File #E188111
Flame Autoextinguish:   94-V0
Operating Temperature:   -40º C to +85º C
Insertion/Extraction Life:   1000 Minimum Cycles
Contact Resistance:  10 Milli-Ohms maximum
Current/Voltage:   30 VAC/42 VDC at 1.5 Amps
Compliance:   RoHS Compliant

COMPLEMENTARY PRODUCTS TO DO THE JOB RIGHT



900005
(with factory installed die set 900216)

    


TERMINATION TOOL

Professional Grade - Controlled Ratchet Style
Insures Proper Blade Setting Depth
1,000,000 Cycles Minimum

 
DO NOT TAKE THIS STEP FOR GRANTED
Cable assemblies built using inadequate or poor quality tools and dies.....worn out tooling.....or mismatched tooling, WILL HAVE A MAJOR IMPACT ON THE PERFORMANCE
OF THE CABLE ASSEMBLY.

106-08080058-34 Termination Instructions  


 111-08080090L34 Termination Instructions  





                         
900005


111-08080090L34











3M™ 1181


 

PROPER CABLE PREPARATION INCLUDES COPPER SHIELDING TAPE TO MAINTAIN SHIELD INTEGRITY & PROVIDING A PLACE FOR THE "C CRIMP" SHIELD ON THE CABLE

3M™
1181
1/2" Copper Foil
Shielding Tape
with Conductive Adhesive




LOAD BAR SHOWN IN PICTURE

  

3M 1181 Copper Foil Shielding Tape
 




           
SNAGLESS STRAIN RELIEF BOOT OPTIONS

RECOMMENDED
 
  8MM
SNAGLESS BOOT
Accepts up to 8MM Jacket OD (.314")

Care must be taken to fully wrap the C CRIMP around the Cable (360º) to insure proper fit. Six (6) available colors:  B0041 (Gray)   B0042 (Blue)  B0043 (White)  B0044 (Yellow)   B0051 (Black)   B0052 (Clear)



B0041 Gray

B0042 Blue

B0043 White

B0044 Yellow

B0051 Black

B0052 Clear


   
 


EPS-300


3M™ HEAT SHRINK TUBING


1/2 Inch Diameter
Adhesive-Lined, 3:1, Flexible, Polyolefin

"Lock" Everything in Place
Sold in 3 Inch Lengths

 

EPS-300 Heat Shrink




The RJ-45 Is A Highly Engineered Interconnection System

CAVEAT EMPTOR.....Let The Buyer Beware

SUB-STANDARD, NON-COMPLIANT and COUNTERFEIT RJ45's coming in from the Far East

KNOW THE STANDARDS - KNOW THE SPECS - INSIST ON COMPLIANCE - KNOW YOUR SUPPLIERS


For more information, contact
dave@rj45s.com

RJ45s.com
2400 East Main Street
St Charles, IL 60174
phone: 630-659-6337
fax: 888-210-4593



                                                                                                                        


Website Builder