RJ45 TERMINATION TOOLS

The Final Critical Step
Sentinel Connector RJ45 Termination Tools

Two types of RJ45 (8P8C) plugs and installation tools (used for crimping the plug onto a cable) are commonly available: Western Electric/Sentinel Connector (WE/SCS) and Tyco/AMP. While both types look remarkably similar, the tooling used to install the two different plug types is mutually exclusive and cannot be interchanged between the two types. WE/SCS compatible plugs are available from a large number of manufacturers, whereas Tyco/AMP plugs are produced exclusively by Tyco Electronics. Both types of modular plugs will plug into the same standard 8P8C modular jack.

WE/SCS and Tyco/AMP RJ45 (8P8C) plugs have different spacing for the cable strain relief. As a result, using a WE/SCS crimp dieset on a Tyco/AMP RJ45 plug will crush the top of the connector and damage the crimp dieset, and vice versa. While the WE/SCS compatible plug is produced by a larger number of manufacturers than the Tyco/AMP plug, it is still important to know what style is being used to avoid damaging the plug or tool during crimping.

DO NOT TAKE THIS STEP FOR GRANTED

Many times, cable assemblies are built using inadequate or poor quality tools and dies.....worn out tooling.....or mismatched tooling. THIS WILL HAVE A MAJOR IMPACT ON THE PERFORMANCE OF THE CABLE ASSEMBLY. Here are a few examples.....if the tooling is worn out, the blades (contacts) will not be set to the proper nominal dimensions as set forth by the FCC Part 68.5 (included in TIA-968) . In addition, worn out or mismatched tooling might actually "peel off" part of the RJ-45 plastic insulation ("orange peel effect") thereby covering the contact with the plastic causing intermittencies or loss of signal. NOTE: POOR QUALITY TOOLS AND DIES WEAR OUT VERY QUICKLY.....and they should be monitored for usage and expected useful life.

THE SENTINEL ADVANTAGE
PROFESSIONAL GRADE

Ratchet Style - Controlled Cycle Hand Tools

All of Sentinel Connector Systems tooling is made with PRODUCTION GRADE STEEL and the DIE SETS have a MINIMUM EXPECTED LIFE OF 1,000,000 TERMINATIONS. Each factory built tool is "MATCHED UP" to the plug it is designed to terminate.....and if you follow termination instructions properly, you will get a properly terminated cable assembly that meets all of your electrical and mechanical specifications.

SENTINEL OFFERS THE SUPPORT YOU NEED FOR ANY QUESTIONS YOU MAY HAVE REGARDING TOOLING, TERMINATION PROCEDURES and BEST PRACTICES.....WE ARE HERE TO HELP YOU SUCCEED.

THE PROPER BLADE DEPTH AS PUBLISHED IN ANSI/TIA-1096-A SPECIFICATIONS
(formerly FCC Part 68) is .237" +/-.005".
THIS IS CRITICAL TO INSURE PROPER CONTACT MATING
BETWEEN THE PLUG AND JACK
Part Number Description Unit Price
900005/900216
COMES WITH FACTORY
INSTALLED DIE SET 900216
FOR USE WITH STANDARD
UNSHIELDED PLUGS
106-080800-34
106-08080058-34
109.080840-24
110-080820-24
111-080800-34
111-0808LB16-34
111-08080028L34
111-08080054L34
111-08080062L34 AND 111-08080063KL34
111-08080090L34
111-08080091L34
111-08080095LA4
111-080800B5LA4
114-040800-34
AND SHIELDED PLUGS
110S080820-24
111S08080016-34
111S08080028L34
111S08080054L34
111S08080056-34
111S08080062L34 AND 111S08080063L34
111S08080090L34
111S08080091L34
111S08080095LA4
900005/900216
900007
COMES WITH FACTORY INSTALLED DIE SET
FOR USE WITH "C CRIMP" STYLE PLUGS
(Crimps the External Strain Relief AND
Plug Contacts at the same time)
FOR USE WITH
106S08080058C34
110S080820C24
111S08080016C34
111S08080028C34
111S08080056C34
111S08080090C34
111S08080091C34
900007
900020
COMES WITH FACTORY INSTALLED DIE SET
FOR USE WITH "H CRIMP" STYLE PLUGS
(Crimps the External Strain Relief AND
Plug Contacts at the same time)
FOR USE WITH
111S08080054H34
111S08080090H34
111S08080091H34
111S08080095HA4
900020
900026
Hand Crimp Tool for External Strain Relief ONLY
For "C Crimp" Style Plugs -Series "C" and "H"
(Secondary Operation for those who have a contact crimp tool)
900026